Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
A queuing system has three queues serviced with round robin scheduling and one low latency queue that holds all voice traffic. Round robin queue 1 holds predominantly UDP traffic, while round robin queues 2 and 3 hold predominantly TCP traffic. The packets in each queue happen to have a variety of DSCP markings per the QoS design. In which queues would it make sense to use a congestion avoidance (drop management) tool? (Choose two) A. The LLQ B. Queue 1 C. Queue 2 D. Queue 3 Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture Which actions must be performed to implement SNMP access to the router? (Choose two) A. Configure a community access string with a read-write privileged to permit access to SNMP B. Authenticate access to MIB objects and functions as embedded passwords C. Set the system contact and location of the SNMP agent on the router D. Obtain values for the 5 minute exponentially moving average of the CPU busy percentage https://www.learncisco.net/courses/icnd-2/network-management/snmp-v1-v2c-v3-overview-and-configuration.html You have the Class B network 172.16.0.0/16 and want to create 16 subnets. What will the new subnet mask be for the 16 subnets? A. /18 B. /19 C. /21 D. /17 E. /22 F. /20 Which of the following statements describe a link state routing protocols? (Choose two) A. Each router builds its own internal map of the network topology B. Update messages are propagated to all routers running the same routing protocol C. Periodic update messages are sent whether there is a change in the network or not D. Only concerned with how far and in what direction the destination is https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/dynamic-routing.html In a split-MAC architecture, real-time functions such as encryption are handled in which of the following network entities? A. An access layer switch B. A distribution layer switch C. A wireless LAN controller D. A lightweight AP Consider the following scenario: Host A has IP address 192.168.6.3 and MAC address 0800:0111:3333. Host B has IP address 192.168.7.3 and MAC address 0800:0222:4444. The router has IP address 192.168.7.1 and MAC address 0800:0444:1111. When Host B receives a packet from Host A, the frame contains the source and destination IP and MAC addresses. What should be the destination IP address? A. 0800:0444:1111 B. 192.168.7.3 C. 192.168.6.3 D. 0800:0222:4444 https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html __________ means that the QoS tool changes one or more header fields, setting a value in the header. A. Marking B. Classifying C. Insertion D. Qualifying Refer to the diagram. What is the name of the device referenced with the arrow, assuming the traffic coming from the wireless clients followed the dashed path? A. Autonomous AP B. Lightweight AP C. Wireless controller D. Wireless router Which UTP cable category introduced 1Gbps throughput? A. 6 B. 5e C. 5 D. 3 You are setting up remote access on your Cisco IOS switch. What is the purpose of the “login“ command when issued in [line vty] configuration mode? A. It prompts remote users to provide a password B. It allows remote users to connect without a password C. It enables remote login D. It disables remote login E. It grants the login privileged level Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 Which commands are used to statically assign an IPv6 address to a device using a manual interface ID? (Choose two) A. interface Ethernet0/0 B. ipv4 address 2001:DB8:2222:7272::72/64 C. ipv6 address 2001:0DB8:0:1::/64 eui-64 D. ipv6 address 2001:DB8:2222:7272::72/64 When comparing next-generation IPS to traditional IPS, what additional capabilities can be leveraged to more efficiently block traffic? (Choose three) A. AVC B. Signature-based filtering C. Contextual awareness D. Event impact level Which command could you enter to encrypt passwords? A. enable secret B. username {username} secret {password} C. service password-encryption D. All of the above E. None of the above What are the benefits of implementing IPv6? (Choose four) A. Transition richness B. Larger address space C. Simpler header D. Security and mobility E. Smaller address space F. Complex header Which cloud service model gives a customer complete control over the virtual hardware components, including processor performance, network connectivity, how much memory and storage space is required, and potentially the operating system that is preinstalled? A. SaaS B. IaaS C. PaaS D. TaaS Which port state is introduced by Rapid-PVST? A. learning B. listening C. discarding D. forwarding https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html How can be secured a console access to a network device? A. Encrypt the console password B. Define RSA keys to be used in authentication C. Generate a certificate key https://www.learncisco.net/courses/icnd-1/lan-connections/cisco-router-security.html Which command correctly assigns a subinterface to VLAN 8 using 802.1Q trunking? A. Router(config-if)#encapsulation 802.1Q vlan 8 B. Router(config-if)#encapsulation dot1q 8 C. Router(config)#encapsulation 8 dot1q D. Router(config)#encapsulation trunk dot1q 8 https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Which statement is true about the subnet masks /12, /20, and /28? A. They all have the same number of network bits B. They all have the same block size of 16 C. They all create only 16 subnets D. They all have the same number of host bits Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet? A. 802.3ad B. 802.1w C. 802.1D D. 802.1Q https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/dynamic-trunking-protocol.html Which IOS command always displays OSPF hello timer settings? A. show ip protocols B. show ip route C. show ip ospf interface D. show ip ospf neighbor E. debug ip ospf events The Wi-Fi Alliance offers which of the following certifications for wireless devices that correctly implement security standards? A. WEP B. WPA2 C. 802.11 D. AES An engineer connects to Router R1 and issues a show ip ospf neighbor command. The status of neighbor 2.2.2.2 lists FULL/BDR. What does the BDR mean? A. R1 is an Area Border Router. B. R1 is a backup designated router. C. Router 2.2.2.2 is an Area Border Router. D. Router 2.2.2.2 is a backup designated router. What are some perceived benefits of controller-based networks as compared to traditional networks? (Choose two) A. New operational models that allow for a single device to be instantiated with the entire network in mind B. The use of APIs to mass-configure network devices, allowing for more consistency and fewer errors C. The use of DevOps approaches in the network to increase efficiency and productivity D. The use of legacy approaches in the network to increase efficiency and productivity When planning a greenfield SDA design, what traditional LAN design points should be included? (Choose two) A. The number of switchports needed in each switch B. The required speed of the switchports C. A security firewall to properly segment traffic D. The Spanning Tree mode of operation to use You can use the Cisco IOS ”copy” command to move configurations from one component or device to another. Which of the following commands will save the recent configuration changes to the NVRAM? A. erase startup-config B. copy tftp running-config C. copy running-config tftp D. copy running-config startup-config https://www.learncisco.net/courses/icnd-1/network-environment-management/managing-devices.html Which of the following are available methods of classifying packets in DiffServ on Cisco routers? (Choose three) A. Matching the IP DSCP field B. Matching the 802.1p CoS field C. Matching fields with an extended IP ACL D. Matching the SNMP Location variable Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true? (Choose two) A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached. B. Router C will use ICMP to inform Router B that Host 2 cannot be reached. C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached. D. Router C will send a Destination Unreachable message type. E. Router C will send a Router Selection message type. F. Router C will send a Source Quench message type. Choose the correct order from the following steps for a physical Cisco Catalyst switch startup process. 1. Verify the boot sequence. 2. Follow proper procedures of mounting the physical device 3. Ensure the security of all network cable connections 4. Attach the power cable plug to the switch`s power supply 5. Check the requirements for power and environmental conditions A. 1, 2, 3, 4, 5 B. 3, 4, 2, 1, 5 C. 5, 3, 1, 2, 4 D. 5, 2, 3, 4, 1 E. 4, 1, 2, 5, 3 https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html You have connected to your Cisco IOS router using SSH for remote management. You have entered the command “debug ip rip“ to verify that RIP updates are being sent and received by the router. You wait for 90 seconds and notice that no RIP updates are being sent or received. After reviewing the RIP configuration, you conclude that the configuration is fine. You also verify that logging to the vty lines is set to debugging. Why are you not seeing the RIP updates? A. You need to issue the logging monitor 7 command B. You need to wait longer since RIP updates are every 180 seconds C. Debugs are not available for vty sessions D. You need to enable RIP E. You need to connect to the console port first F. You need to issue the terminal monitor command How do packet forwarding and path determination function on a router? (Choose two) A. Routers must maintain a common routing table to ensure that other routers know about changes in the network B. The destination IP address in the packet defines the packet destination C. A router determines the source of the information using the first number in each line of the show ip route output D. The routing table holds only one entry per network What option(s) are required criteria for a service to be a cloud service? (Choose two) A. Rapid elasticity B. Agile network access C. Measured service D. Proactive service You need to create an ACL entry that will only permit all addresses in the 10.1.1.16/28 network. Which address and wildcard mask combination will accomplish this for us? A. 10.1.1.16 0.0.0.31 B. 10.1.1.16 0.0.0.63 C. 10.1.1.16 0.0.0.255 D. 10.1.1.16 0.0.0.15 E. 10.1.1.16 0.0.0.3 F. 10.1.1.16 0.0.0.7 Which command would you use to enter the OSPF routing configuration mode? A. Router(config-router)#network 10.0.0.0 0.0.0.255 0 B. Router(config)#router ospf 1 C. Router(config)#network 10.0.0.0 0.0.0.255 area 0 D. Router(config)#router ospf https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/single-area-ospf.html A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config A switch’s port Gi0/1 has been correctly enabled with port security. The configuration sets the violation mode to restrict. A frame that violates the port security policy enters the interface, followed by a frame that does not. Which of the following answers correctly describe what happens in this scenario? (Choose two) A. The switch puts the interface into an err-disabled state when the first frame arrives. B. The switch generates syslog messages about the violating traffic for the first frame. C. The switch increments the violation counter for Gi0/1 by 1. D. The switch discards both the first and second frame. Which of the following four TCP/IP layers determines the best path through the network? A. Network Access B. Transport C. Internet D. Application https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Why doesn't increasing the number of uplinks solve congestion issues from multiple links aggregating on a switch? A. All traffic must pass through one physical link B. Multiple links require extra overhead C. All uplinks must be running at the same speed D. STP disables ports to prevent loops If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 How does 802.1q identify the VLAN that the frame belongs to while it crosses the trunk link? A. It encapsulates the entire frame with a 30 byte header and FCS B. It encapsulates the entire frame with a 30 bits header and FCS C. It places a 4 byte tag after the source MAC address in the frame D. It places a 4 bit tag after the source MAC address in the frame Which of these are QoS requirements when designing a Cisco TelePresence video network? (Choose two) A. One-way delay < 200 ms B. Round-trip delay < 200 ms C. Loss < 5% D. Loss < 0.05% E. Jitter < 100 ms F. Jitter < 50 ms Which of the following commands will display one line of information per port channel? A. show etherchannel summary B. show interface port-channel C. show etherchannel port-channel https://www.learncisco.net/courses/icnd-2/etherchannel-and-l3-redundancy/configuring-etherchannel.html You have implemented stateless address autoconfiguration in your local area network. What will the end stations use as their default gateway address? A. The link-local address of the router's interface B. A special default gateway address that is provided in the router advertisement C. The unique local address of the router's interface D. The global address of the router's interface E. The anycast address of the router's interface Which option should be used with the “switchport trunk allowed vlan“ command to include specified VLANs in the existing list of allowed VLANs on a trunk link? A. add B. except C. remove D. none E. all Which statements are true about telnet and ssh? (Choose two) A. Only data traffic is encrypted with ssh B. All telnet traffic is sent in plain text C. All ssh traffic is encrypted D. The data is hashed by telnet during transmission E. The username and password is hashed by telnet during authentication F. Only authentication traffic is encrypted with ssh When using NAT to translate private IPv4 addresses to public IPv4 addresses, what term is used to identify the private IPv4 address? A. Inside local B. Outside local C. Outside global D. Inside global Which of the following best describes a virtual network function in a public cloud service? A. A subset of a physical networking device, configured by the cloud provider and allocated for use by that customer only B. A networking function implemented by the cloud provider for the customer, but with no direct customer access to the server that provides the service C. A networking function implemented by the cloud provider for the customer as a VM that is directly accessible and configurable by the customer D. Any networking feature implemented on a VM in a cloud service What is the name of the protocol that has been developed by the ONF that is used to communicate between an SDN controller and the network devices it controls? A. OpFlex B. OpenSDN C. SbControl D. OpenFlow Which features are used to extend the lifetime and usefulness of IPv4 networks? (Choose four) A. Private Addressing B. VLSM C. CIDR D. VLANs E. Public Addressing F. NAT G. IPv6 Suppose two APs are located near each other. Which channel use strategy will result in nonoverlapping channels for Wi-Fi use? (Choose two) A. Use 2.4-GHz channel 1 on AP-A and channel 2 on AP-B. B. Use 2.4-GHz channel 1 on AP-A and 5-GHz channel 48 on AP-B. C. Use 5-GHz channel 36 on AP-A and channel 40 on AP-B. D. Use 5-GHz channel 36 on AP-A and channel 37 on AP-B. Which of the following OSPF packet types sends missing information to the neighbors? A. link-state acknowledgement, or LSAck B. link-state update, or LSU C. link-state request, or LSR D. database description package, or DBD https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/link-state-databases.html

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources