Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Identify the commands used to correctly configure multiarea OSPF. (Choose two) A. OSPF can be enabled universally within an area by using the [ip ospf area] command on any router within a specific area. B. The [ip ospf cost] command specifies the OSPF cost of sending a packet on an interface. C. The [network area] command defines the interfaces on which OSPF runs and defines the area IDs for those interfaces. D. Individual routers can only be configured with a single OSFP routing process number using the [router ospf] command. https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/multiarea-ospf-configuration.html Which of the following OSPF packet types describes the network routes of each neighbor? A. link-state acknowledgement, or LSAck B. link-state update, or LSU C. link-state request, or LSR D. database description package, or DBD https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/link-state-databases.html What is the purpose of the “service password-encryption“ command? A. It encrypts all passwords on your router. B. It encrypts the line console password only. C. It encrypts the vty password only. D. It is not a valid cisco command What is the calculator of the total cost of a particular path referred to? A. Checksum B. Metric C. Bandwidth D. Length You are configuring your edge routers interface with a public IP address for Internet connectivity. The router needs to obtain the IP address from the service provider dynamically. Which command is needed on interface FastEthernet 0/0 to accomplish this? A. ip default-gateway B. ip route C. ip default-network D. ip address dhcp E. ip address dynamic You are subnetting the 172.16.0.0/16 network so that you have 100 subnets. How many bits do you need to borrow, what is the new subnet mask, and how many hosts will be in each subnet? (Choose three) A. There will be 254 possible hosts in each subnet B. There will be 510 possible hosts in each subnet C. /23 is the new subnet mask D. 7 bits will be borrowed E. 8 bits will be borrowed F. /24 is the new subnet mask What is the name of the firewall feature that, when used, can maintain a historical database of each connection through a device: Where it was sourced, destined, and which protocol and protocol port it was using? A. Stateless Inspection B. Stateful Inspection C. Network Protocol Analysis D. Protocol State Analysis If a lightweight AP provides at least one BSS for wireless clients, which one of the following modes does it use? A. Local B. Normal C. Monitor D. Client Which DSCP Assured Forwarding value provides the worst drop and worst queue performance? A. AF41 B. AF43 C. AF11 D. AF13 Review the topology. All subnets exist in OSPF area 0. Which command, if issued on R3, would show all the LSAs known by R3? A. Show running-config B. Show ip ospf interface C. Show ip ospf neighbors D. Show ip route ospf E. Show ip ospf database You are configuring dynamic NAT on your Cisco IOS router. Which command is used to verify the interfaces that are being used as the outside interface and the inside interface? A. show interfaces B. show ip route C. show ip nat translations D. show ip interface brief E. show ip interface F. show ip nat statistics Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 What is the administrative distance of RIPv2? A. 110 C. 90 D. 100 E. 1 F. 120 G. 5 Which shorthand notations can be applied to IPv6 addresses? (Choose three) A. An unspecified address is written as a double colon followed by four zeros B. Leading zeros in a field are optional C. Format is x:x:x:x:x:x:x:x, where x is a 16-bit hexadecimal field D. Successive fields of 0 are represented as "::" but only once in an address E. Hexadecimal digits A-F are case sensitive https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html Which command could you enter to encrypt passwords? A. enable secret B. username {username} secret {password} C. service password-encryption D. All of the above E. None of the above What is known as “one-to-nearest“ addressing in IPv6? A. global unicast B. anycast C. multicast D. unspecified address https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html Choose the correct order from the following steps for a physical Cisco Catalyst switch startup process. 1. Verify the boot sequence. 2. Follow proper procedures of mounting the physical device 3. Ensure the security of all network cable connections 4. Attach the power cable plug to the switch`s power supply 5. Check the requirements for power and environmental conditions A. 1, 2, 3, 4, 5 B. 3, 4, 2, 1, 5 C. 5, 3, 1, 2, 4 D. 5, 2, 3, 4, 1 E. 4, 1, 2, 5, 3 https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html Which of the following parameters are necessary when creating a new WLAN with the controller GUI? (Choose two) A. SSID B. VLAN number C. Interface D. BSSID E. IP subnet An enterprise plans to start using a public cloud service, and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Which of these are QoS requirements when designing a Cisco voice network? (Choose two) A. Jitter < 30 ms B. Loss < 1% C. One-way delay < 200 ms D. Jitter < 50 ms E. Loss < 2% F. Round-trip delay < 200 ms During a maintenance window, you make some changes to R2. You document these changes in your configuration management system. Later that night, you are called in to fix an issue that requires you to make additional changes to R2. The next morning your co-worker addresses another issue but this time on R1. All of these changes are documented properly but neither you or nor your coworker discuss the changes. These changes stay implemented for months. What is this best described as? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. Host A and Host B sit in two different subnets. The path between the subnets of these two hosts runs through three different Layer 3 forwarding devices (routers and Layer 3 switches). A network engineer uses the APIC-EM Path Trace ACL Analysis tool to analyze the path used for Host A to send packets to Host B. Which part of the function is done specifically by the ACL Analysis or ACL Trace part of the tool? A. Discovery of the topology that exists between the two hosts B. Analysis of the Layer 3 forwarding decisions in the path from Host A to B C. Analysis of the Layer 2 forwarding decisions in the path from Host A to B D. Analysis of the impact of ACLs on the packets that would flow from Host A to B Review the following router configuration and identify the correct statements regarding telnet access to the router: Router(config)#access-list 1 deny host 10.1.20.1 Router(config)#access-list 1 deny host 10.1.20.2 Router(config)#access-list 1 permit host 10.1.10.1 Router(config)#access-list 1 permit host 10.1.10.2 Router(config)#access-list 1 permit 10.1.20.0 0.0.0.255 Router(config)#line vty 0 4 Router(config-line)#access-class 1 in (Choose two) A. Telnet access from all hosts in the 10.1.20.0/24 network is denied except 10.1.20.1 and 10.1.20.2 B. Telnet access from hosts 10.1.20.1 and 10.1.20.2 is allowed C. Telnet access from hosts 10.1.10.1 and 10.1.10.2 is allowed D. Telnet access from all hosts in the 10.1.10.0/24 network is allowed E. Telnet access from all hosts in the 10.1.20.0/24 network is allowed except 10.1.20.1 and 10.1.20.2 F. Telnet attempts that are denied will generate a syslog message You have configured one side of your EtherChannel as passive. What mode should you use on the other side? A. Desirable B. On C. Auto D. Active Which of the following components holds the diagnostic software that is used when the router powers up? A. Interface B. ROM C. Flash D. RAM E. CPU F. NVRAM https://www.learncisco.net/courses/icnd-2/network-management/router-internal-components-overview.html What steps are involved in configuring a SPAN session? (Choose three) A. Associate a SPAN session number with the source port of VLANs B. Associate a SPAN number with the destination C. Instruct the router to copy all traffic that it sends and receives D. Verify the configuration E. Configure the destination port as a source port Historically, your organization has modified the network device configuration by logging in to the local devices manually. Today, your new CIO has enforced that all configuration changes should be completed on a server in the data center and then pushed out. Which answer lists the correct term for this new approach to configuration? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which physical layer media is not susceptible to electromagnetic interference? A. Twisted copper pair B. Wireless C. Coaxial D. Fiber optic Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture With IEEE 802.1x, which role does a LAN switch typically play? A. Authentication server B. Supplicant C. Translator D. Authenticator What are the valid encapsulation methods when forcing a device to become a trunk port? (Choose three) A. private-vlan B. dot1q-tunnel C. dot1q D. negotiate E. isl You need to create 8 subnets in the 192.168.1.0/24 network. What is the new network mask that will be used and how many hosts can be used on each of the subnets? (Choose two) A. 30 hosts B. 126 hosts C. Network mask /27 D. Network mask /25 E. Network mask /26 F. 62 hosts https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html What is the name of the Cisco product that offers a number of rack-mountable server configurations intended to be used in data centers? A. ASA B. KVM C. CRC D. UCS A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch? A. More collision domains will be created. B. IP address utilization will be more efficient. C. More bandwidth will be required than was needed previously. D. An additional broadcast domain will be created. https://www.learncisco.net/courses/ccna/part-5-virtual-lans-vlans/vlans-review.html Which of the following cloud services is most likely to be purchased and then used to later install your own software applications? A. IaaS B. PaaS C. SaaS D. SLBaaS How are ACLs processed? A. Entries are processed bottom-up B. Entries are processed top-down C. Entries are processed at the same time D. Entries are processed randomly How is Telnet used to verify connectivity? (Choose two) A. It shows you the path required to reach the end device B. To determine if you have access to a particular service on a device C. It uses ICMP Echo requests to test connectivity D. To verify basic connectivity to a device Which command displays information about security options configured on an interface? A. show port-security interface [interface-id] B. show port-security [interface-id] C. show port-security[address] D. show security [interface-id] What are some perceived benefits of controller-based networks as compared to traditional networks? (Choose two) A. New operational models that allow for a single device to be instantiated with the entire network in mind B. The use of APIs to mass-configure network devices, allowing for more consistency and fewer errors C. The use of DevOps approaches in the network to increase efficiency and productivity D. The use of legacy approaches in the network to increase efficiency and productivity Which commands will successfully create VLAN 5 and name it SALES on a Catalyst IOS switch? A. Switch(config)#vlan 5 Switch(config-vlan)#name SALES B. Switch(config)#vlan 5 Switch(config)#name SALES C. Switch#vlan 5 Switch(config-vlan)#name SALES D. Switch(config)#vlan 5 name SALES E. Switch(config)#vlan 5 Switch(config-vlan)#SALES Which dynamic routing protocols are examples of link-state routing protocols? (Choose two) A. BGP B. RIP C. EIGRP D. OSPF E. IS-IS On a Cisco IOS ISR, which layers of the OSI model can you verify with the output of ”show ip interface brief” command? (Choose three) A. Layer 5 B. Layer 1 C. Layer 2 D. Layer 6 E. Layer 7 F. Layer 3 G. Layer 4 Which options are not one of the manageable QoS characteristics of network traffic? (Choose two) A. Delay B. Jitter C. Queue size D. Clock rate E. Bandwidth F. Loss Which layer of the OSI model defines how data is formatted for transmission? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html You have a network address of 172.16.0.0/22, which equals a subnet mask of 255.255.252.0. Determine the block size of this subnet. A. 6 B. 8 C. 2 D. 16 E. 4 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Which command is used to set your Cisco IOS device as an authoritative time source that will be used as the trusted time source? A. ntp master B. ntp server C. ntp client D. ntp peer Which of the following describes the RSTP protocol? A. Assumes one 802.1D spanning tree for the entire bridged network B. Provides a separate 802.1D spanning tree for each virtual LAN, or VLAN, configured C. Provides fast conversion with a single instance of STP D. Provides fast conversion with an instance of spanning tree per VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html You have the network 192.168.5.0/24 that has been subnetted to /30 networks. What is the subnet ID of the seventh subnet that was created? A. 192.168.5.28/30 B. 192.168.5.16/30 C. 192.168.5.12/30 D. 192.168.5.24/30 E. 192.168.5.32/30 F. 192.168.5.20/30 Which command is used to verify the DHCP relay agent address that has been set up on your Cisco IOS router? A. show ip interface brief B. show ip dhcp bindings C. show ip route D. show ip interface E. show interface F. show ip dhcp pool Which statements correctly describe a standard IPv4 ACL? (Choose two) A. Uses protocols and port numbers for matching B. Uses source and destination IP address for matching C. Permits or denies the entire protocol suite D. Only uses the source IP address for matching E. Can only be created as numbered ACLs Think about a policing function that is currently working, and also think about a shaping function that is also currently working. That is, the current bit rate of traffic exceeds the respective policing and shaping rates. Which statements are true about these features? (Choose two) A. The policer may or may not be discarding packets. B. The policer is definitely discarding packets. C. The shaper may or may not be queuing packets to slow down the sending rate. D. The shaper is definitely queuing packets to slow down the sending rate. Suppose two APs are located near each other. Which channel use strategy will result in nonoverlapping channels for Wi-Fi use? (Choose two) A. Use 2.4-GHz channel 1 on AP-A and channel 2 on AP-B. B. Use 2.4-GHz channel 1 on AP-A and 5-GHz channel 48 on AP-B. C. Use 5-GHz channel 36 on AP-A and channel 40 on AP-B. D. Use 5-GHz channel 36 on AP-A and channel 37 on AP-B.

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources